![]() Industry terms that may be deemed inappropriate by our customers. This process, however, our content may still contain standardized The Modbus OPC Server is a powerful tool that enables a secure access to your Control and Automation systems and opens new connectivity horizons to other. Of a group of responsible, inclusive companies, we are updating ourĬommunications that contain non-inclusive terminology. To the extent permitted by applicable law, no responsibility or liability is assumed by Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein. Schneider Electric products and equipment should be installed, operated, serviced, and maintained only by qualified personnel.Īs standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice. The Modbus-Square D PowerLogic Ethernet OPC Server supports data exchange with Clients via Microsofts Object Linking and Embedding (OLE) for Process Control (OPC). Input: power meter modbus unitid, also added value unitid in output JSON object. Schneider Electric does not grant any right or license for commercial use of the guide or its content, except for a non-exclusive and personal license to consult it on an "as is" basis. Subflow to obtain data from Schneider POWERLOGIC PM5150 via MODBUS TCP. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of Schneider Electric. This guide and its content are protected under applicable copyright laws and furnished for informational use only. All other brands may be trademarks of their respective owners. NOTE: Not all firmware revisions are capable of TCP modbus mastering.The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this guide are the property of Schneider Electric SE or its subsidiaries. The following tables indicate which data is available in the EcoStruxure Panel Server according to each type of sensors. Refer to the ION Reference manual on more details on meter modules and their functions: ION Reference Manual The data transmitted by the PowerTag Energy and PowerLogic Tag sensors and Acti9 Active to the EcoStruxure Panel Server depends on the type of sensors. ![]() Under the Slave Name, give a name to the slave device.(Same name entered in Modbus Master Map Module) Enter the device type for the slave device.Enter the unit ID of the slave device.Select the connection type (Serial or TCP).Double Click on Modbus Master Device module. Adding a Powerlogic Device via Modbus Ethernet Gateway to ION Setup Schneider Electric Support Schneider Electric 173K subscribers Subscribe 50 Save 28K views 6 years ago PowerLogic.Connection, Slave address, Device Name and Slave name, you may leave comms error at default). Step 4: Enter the exact device type and connection properties into the Modbus Master Device Module (i.e. Double click on Device Map, enter the device map following the format in the FAQ FA235162.In Setup Registers tab, double click on device Type and enter device name and click OK.Double click on the new module that you created.Right click in the right pane > Insert Module.NOTE: Refer to FA235176 for supported formats used in the Modbus Master Map Module. Step 3: Enter the Modbus map of your slave device(s) into the Modbus Master Map Module. If the folder is empty, right click on the right pane > Insert module, otherwise proceed to next step. The Panel Server acts as a Modbus gateway for wired or wireless Ethernet communications from an upstream PC to Ethernet devices and field devices on the.While holding on the Ctrl key, left click on your meter.Step 2: Enter Advanced mode, and set the MMO1 Serial Connection 1 in the Modbus Master options module Setup register to the communication port your slave device is connected to on the master device. Set the Com port unit ID to a unique number.i.e these settings should be identical on all devices. Set the baud rate, stop bits and parity to be the same as on your slave device(s).Click on communications > Serial Settings.Double click on Setup assistant in the right pane.Click on the View Setup Options Only tab from the tool bar.In ION Setup, click on the Master Device that you want to set up.Step 1: Setup communication protocol for Modbus mastering. How to configure modbus mastering of downstream devices on ION and Powerlogic meters.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |